Over/Under Voltage Cut-off with On-Time Delay

Here is an inexpensive auto cutoff circuit, which is fabricated using transistors and other discrete components. It can be used to protect loads such as refrigerator, TV, and VCR from undesirable over and under line voltages, as well as surges caused due to sudden failure/resumption of mains power supply. This circuit can be used directly as a standalone circuit between the mains supply and the load, or it may be inserted between an existing automatic/manual stabilizer and the load. 

Parallel Port Logic Analyzer

When you build a digital electronic project and have trouble with it you need a device to debug it. To analyze logic output from your project you need a Logic Analyzer. 
If you don’t have it you can try to build by yourself cheap logic analyzer device using parallel port. The device only use few resistors and IC 74HC245 as data buffer. To display the graphical output from logic analyzer device you can use Fabulous Logic Analyzer software, here.


Schematic:

Parallel Port logic analyzer

Component Required:
IC1,               74HC245
R1-R8,         10K ohm
R9-R16,       100 ohm
R17,              2K ohm
LED
DB25 Male, Parallel Port Connector

Telephone Operated Remote Control v2 Using PIC16F876A

This is a newer version of previous device. This one can have up to 6 relays and 6 sensor-state inputs.
The task was to build a device that connects to the phone line and has a relay as an output switch. It should also sense if the connected «consumer» is turned-on or off and report to the administrator at the other end of the phone line. The administrator would then call-in the device, log in with the password, and check the state of «consumer», turn it on or off, change password or some other settings.


Download: Schematic, Program files And Documentation


Schematic:

Full Schematic

Telephone operated remote control

Telephone Operated Remote Control Using PIC16F84A

This design controls up to 8 devices using a PIC microcontroller (PIC16F84A) connected to the phone line. The unique feature here is that unlike other telephone line based remote control, this device does not need the call to be answered at the remote end so the call will not be charged. This device depends on number of rings given on the telephone line to activate/deactivate devices.

PIC16F887/877 programming in C Tutorial 10 (ADC)

Analog to Digital Converter (ADC):

In this tutorial i will show how to convert analog values into digital, by using 887 (little bit differ with 877), then display these digital value on LCD.

The Analog-to-Digital Converter (ADC) allows conversion of an analog input signal to a 10-bit binary representation of that signal. This device uses analog inputs, which are multiplexed into a single sample and hold circuit. The output of the sample and hold is connected to the input of the converter. The converter generates a 10-bit binary result via successive approximation and stores the conversion result into the ADC result registers (ADRESL and ADRESH).

The ADC voltage reference is software selectable to be either internally generated or externally supplied.

ADC Configuration:
When configuring and using the ADC the following functions must be considered:
• Port configuration
• Channel selection
• ADC voltage reference selection
• ADC conversion clock source
• Interrupt control
• Results formatting

Port configuration:
The ADC can be used to convert both analog and digital signals. When converting analog signals, the I/O pin should be configured for analog by setting the associated TRIS and ANSEL bits.

Channel selection:

The CHS bits of the ADCON0 register determine which channel is connected to the sample and hold circuit. When changing channels, a delay is required before starting the next conversion.

ADC voltage reference selection:

The VCFG bits of the ADCON0 register provide independent control of the positive and negative voltage references. The positive voltage reference can be either VDD or an external voltage source. Likewise, the negative voltage reference can be either VSS or an external voltage source. 

ADC conversion clock source: 

The source of the conversion clock is software selectable via the ADCS bits of the ADCON0 register. There are four possible clock options:
• FOSC/2
• FOSC/8
• FOSC/32
• FRC (dedicated internal oscillator)
The time to complete one bit conversion is defined as TAD. One full 10-bit conversion requires 11 TAD periods as shown in Figure.

Interrupt control:

The ADC module allows for the ability to generate an interrupt upon completion of an Analog-to-Digital conversion. The ADC interrupt flag is the ADIF bit in the PIR1 register. The ADC interrupt enable is the ADIE bit in the PIE1 register. The ADIF bit must be cleared in
software. 

Results formatting: 

The 10-bit A/D conversion result can be supplied in two formats, left justified or right justified. The ADFM bit of the ADCON0 register controls the output format. 

ADC Operation:

STARTING A CONVERSION:To enable the ADC module, the ADON bit of the ADCON0 register must be set to a ‘1’. Setting the GO/DONE bit of the ADCON0 register to a ‘1’ will start the Analog-to-Digital conversion. 

COMPLETION OF A CONVERSION:When the conversion is complete, the ADC module will:
• Clear the GO/DONE bit
• Set the ADIF flag bit
• Update the ADRESH:ADRESL registers with new conversion result

A/D CONVERSION PROCEDURE:
This is an example procedure for using the ADC to perform an Analog-to-Digital conversion:
1. Configure Port:
• Disable pin output driver (See TRIS register)
• Configure pin as analog
2. Configure the ADC module:
• Select ADC conversion clock
• Configure voltage reference
• Select ADC input channel
• Select result format
• Turn on ADC module
3. Configure ADC interrupt (optional):
• Clear ADC interrupt flag
• Enable ADC interrupt
• Enable peripheral interrupt
• Enable global interrupt(1)
4. Wait the required acquisition time(2).
5. Start conversion by setting the GO/DONE bit.
6. Wait for ADC conversion to complete by one of the following:
• Polling the GO/DONE bit
• Waiting for the ADC interrupt (interrupts enabled)
7. Read ADC Result
8. Clear the ADC interrupt flag (required if interrupt is enabled).

ADC REGISTER DEFINITIONS:
The following registers are used to control the operation of the ADC.

Code:

Lets make it easy by using adc library of mikroc. The following code will convert the analog input, at pin RA2, into digital and display it on lcd. As the conversion is of 10-bit, so the range is from 0-1023.

unsigned int temp_res;

// LCD module connections
sbit LCD_RS at RB4_bit;
sbit LCD_EN at RB5_bit;
sbit LCD_D4 at RB0_bit;
sbit LCD_D5 at RB1_bit;
sbit LCD_D6 at RB2_bit;
sbit LCD_D7 at RB3_bit;

sbit LCD_RS_Direction at TRISB4_bit;
sbit LCD_EN_Direction at TRISB5_bit;
sbit LCD_D4_Direction at TRISB0_bit;
sbit LCD_D5_Direction at TRISB1_bit;
sbit LCD_D6_Direction at TRISB2_bit;
sbit LCD_D7_Direction at TRISB3_bit;
// End LCD module connections

char txt1[] = "ADC Example";
char txt[7];
void main() {
/////////// comment for 877/////////////////////////////////////
  ansel=4;                     // Configure AN2 pin as analog
  anselh=0;
  c1on_bit=0;
  c2on_bit=0;
 ////////////////////////////////////////////////////////////////
  TRISA  = 0xFF;              // PORTA is input
  Lcd_Init();
  Lcd_Cmd(_LCD_CLEAR);               // Clear display
  Lcd_Cmd(_LCD_CURSOR_OFF);          // Cursor off
  Lcd_Out(1,1,txt1);
  adc_init();
  do {

    temp_res = ADC_read(2);   // Get 10-bit results of AD conversion
    IntToStr(temp_res, txt);    //int to string conversion
    Lcd_Out(2,1,txt);
  } while(1);
}

adc_init(); This routine initializes PIC’s internal ADC module to work with RC clock. Clock determines the time period necessary for performing AD conversion.

ADC_read(2); 10 or 12-bit unsigned value read from the specified channel (MCU dependent).Parameter channel represents the channel from which the analog value is to be acquired.In this case it is 2.

IntToStr(temp_res, txt); Converts input signed integer number to a string. The output string has fixed width of 7 characters including null character at the end (string termination). The output string is right justified and the remaining positions on the left (if any) are filled with blanks.

Schematic: